Search results

I moved to Maryland last year, I'm 15 min south of BWI. I found some decent roads between Gambrills and Annapolis. St Stevens Church Rd is the one I start at. Not as nice as my favorite 20 minute ride back in Idaho but nice. Low traffic and decent curves. I'd be willing to run it with someone if...

Ok am I the only person wondering what happened to need the cylinder head replaced. And I have no personal knowledge but I thought somewhere on here they decided the intake ports were to different on the r6 head to work with our intake system which up must use due to the frame design. But a few...

Seems to me you'd have to disassemble the headlight to install them. They look like they bolt through a "plate".

And also if your kickstand switch is messed up it won't prime or start in gear must be in neutral

Yep a few years in full time Mechanic work and I don't pull out the torque wrench unless the valve cover is off. I've never used one CCW, and on the lugnuts I don't have specific car but I've heard several times that Chrysler products in the 60's and 70's did, like Chargers and Road Runners

How ever rare there are times you may need to apply torque in the opposite direction. The only one on my mind right now is Old Mopars that had the lugnuts directional to the sides. and there are engine pulleys that are left hand thread.

Ok I have to say your almost countering yourself there, your right Pros tend to have to work on several vehicle a day, and some of them are total junkers and some ride like a vault. That's why you need to tell them your concerns so they have an idea where to start cause they may notice a couple...

Ok just trying to get this clear in my head so bear with me you say the front tire is off an inch from the rear is it like this = _ or more like this = / when it should be like this = -, I bought my first bike damaged and had an experienced rider take it for a spin and still upon tear down...

or 2 weeks ago I was parked at the Firestation with a person that works at that station

Ok prime riding season and this game is dead, I refuse to go to the only biker bars I know of anywhere near me. So Wh0M3 can we get a new challenge, I wish I could of gotten some pics from this weeks ride but time and riding partner didn't allow for it. Next, your bike at a biker bar.

I'm in Post Falls but I am in the Spokane Valley more then I care to admit to.

I think this is what your gonna need to do, I'm going off automotive experience but injectors have a mini screen in the top. And your describing a fuel starvation issue. Theres a shop near me that does it for 16 a piece, I'll give you the link mostly cause I know he does the work and always puts...

Ok sweet, I sent the link to my brother and we poor Americans could not figure out what kind of car it is in?

Good paint cost money, the time difference between painting a fender and a side of a car is really not much difference at all, the painter applies the paint then on a small item like that has to wait for the paint to flash off to put the next layer on, so the painter and his booth can be tied up...

I really wanted to go to the Victory demo day here but it got cancel due to weather and I found out about it to late on the reschedule. That said I did make the Yamaha ride and after a ride on an FJR and an R6 I was happy with my FZ6. The FJR seat was to wide made my hip feel spread out and the...

Something my friend runs on his jeep roll bar are some heavy nylon straps, they go around the roll bar and give you a handle. Not sure if the ones for a rollbar would work, but if someone could make them I think it would be a pretty slick what to do it no permanent mod to bike. here is a quick...

Sorry but I have to say it, Who made the seat cover from dalmatians?

The other day I had my bike out to test the new forks and brakes and the sensor in the dash read 48 at the highest:(. Never climb over 44 till it was running parked. But other then that I've noticed the same always 10+ degrees over ambient after a few minutes.

I had a ninja 500 for almost 5 years, Great beginner bike for me. never rode a 250 except the Honda Nighthawk in MSF. My friend bought the 500 but its parked next to the FZ for the winter. there very similar bikes all in all the FZ I like the 500's taller brother with more athletic abilities.

Depends on the type of paint gun but almost certainly a 1/2 pint should do. With a good HLVP gun less then a quart painted the back end of my brothers car(trunk, 1 door, Spoiler, back bumper, both quarters) after it was rearended.