Search results

Time for a new set of tires. These are my two choices. Note its not the ,road 3. Would like your input on mileages and dry grip. I found the michelins for 30 less. What one would you go with and why.

i have a question for 07+ owners, if you unplug the o2 sensor will it set a code? being a auto tech myself id say yes, but ive read on fourms where people say it dont. so if you have unplugged it and it dont set the light please let me know. i was looking at getting a 02 sensor eliminator...

OK so its been a couple weeks since I did the decat and muffler debaffle, my first o2 readings looked just fine. But I decided to recheck this weekend seeing how I was doing a throttle bodysync, and I've noticed the tone of the exhaust changes in different rpms (not the way it should). The...

Looking at my wiring diagram I went looking to find out what the 4 pin connector was i found mentioned in my other post. I can not find it in the diagram!! I also hve other wires that i suspect to be for additional lights that are not on the diagram,. There not telling us everthing...

was in the middle of doing the grounding procedure for unlocking my CO adjustments while i was looking for a plug to hopefully plug a scan tool into when i came across this plug taped up inside the harness about 3 inches from the ecm connector. it is a 4 pin connector, colors bk/w, bk/w, olive...

was looking at this :confused: kit :confused: Oxygen Sensor O2 Eliminator - Yamaha FZ6 FZ6R FZ1 FZ1N FZ8 FJR1300 | eBay and would like someones feedback who has one. it looks to me to be 1 of 2 things, just a blank plug so water cant get into the plug, thou i doubt it due to the description in...

Would like to here if there were any problems caused by adjusting the CO level. I saw a couple of posts about it but they were from 2009. So time would have told by now for those who did it 4 years ago. Does this work to richen up the fuel mixture enough so you don't have to get a power...

Getting ready to do some more mods and will need to get something to richen up the a/f ratio. Probly will go with a juice box, who knows. Anyway I would like to be able to look at live o2 data so I can figure out just how more rich I need to go. So the questions are what scanner do you...

hia, i plan on taking out the baffles in muffler and hollowing out the 3 cats for the little extra performance gain and some more noise. i have sevral questions and i am a auto tech so if your are a motorcycle tech please dont hesitat to go into detail, here goes. 1. i asked my local shop...

looking into getting a amp/speakers for the bike. anyone use these Sportbike Speakers, Sport Bike Stereo, Streetbike Radio mp3 if so how do they sound at 70 with helmet on. what do you use thats tucked away and sounds good?

looking to buy either just a rear or a set 180/55/17, 120/70/17. if you have a new or near new set and want to sell please contact me. 315-427-5047 or email [email protected] :Flash:

i would like to know if any of you know if the engine bolts used (where you mount the sliders)on the fz6 are the same size diameter bolts as the ones on a R1. i was looking to get a set of offset sliders due to my Yamaha fairings (i dont want to cut them) and have run into these. YAMAHA YZF-R1...

hi again, well if you dont know already i put on the factory full fairing kit for my 07 back in 2007, and have attempted to install sliders. the factory fairing kit is right in the way so i would have to cut the 800.00 fairings :Flip: no way. so i have searched for offset sliders to avoid...

i have checked the manual this time befor asking, but i dont see where is says the recomended lift point is. i do have the center stand but i will be taking both tires off at the same time. i saw a post saying that they used a floor jack/jack stand/ gallon of paint to put under the header...

hi guys, quick question for you. is there a way to adjust the stock headlight buckets? hench changing the aim of the bulbs. my high beam seems to be pointing higher than it should. i have checked to make sure its in the holder the right way. any ideas? :D

have done a quick google search for a indirect frame slider for a 07. i came up with sites explaining what indirect sliders are, but can not find any for sale. anyone now of a site that has these, i have the factory full farings and dont want to cut them to use direct sliders. thanks :Flash:

hi guys, i have noticed that after i wash the bike or I'm caught in a heavy rain fall, after the bike dries and or several hours later that i find what appears to be a rust dropping on my tank which is coming from my turn light/ horn switches. that question of course is how would you prevent...

gonna need a new rear tire soon, and it makes sense to me to get a dual compound tire seeing most of my miles are up and down the interstate. can someone make this easy for me. list all known dual compund tires for me..... ive done a google search and only get a few different tires, would...

attached is the pic of the filter. getting ready for riding season here in CNY i went and did my oil change. this is my first change since i went full syn. (using royal purple, started at 1000mi, at 4300 now.) i noticed 2 little metal flakes on my magnetic drain plug so i was interested to...

hi all, i have done some research and have come up with very few options for a 3 wire led flush mount for a r1, r6, fz1, fz6. what do you guys now about thats out there. im eyeing the protons but i dont much like the price tag on them. thanks ;)