I am about to replace my second Dowco Weatherall Plus cover because the weatherproofing tape failed. Not sure if they will replace the second one under the lifetime warranty, but even if they offer, I want to see what the FZ6 community at large uses as an outdoor cover. I have heard good...
Noticed one of the "caps" on my frame slider is missing. I am the third owner so have no idea what these are. Tried searching on Ebay but no luck. I have 2 pics, one with the blue cover and one without. Where can I order the cover for the other one. Excuse picture quality, dropped my phone...
I broke the chain on my 2006 Fz6 and obviously it broke a couple of things including a bracket that the chain cover bolts to. Do i have to replace the top crank case or is their another cover to the crank case that can be replaced?
I was finishing up the valve adjustment on my 2005 FZ6 and I've run into a bit of a problem... I can't for the life of me get the valve cover seated on!
It almost gets on but ends up off angled hitting the right side of the frame by the chain cover. Any advice on getting in back on?
As stated in title. I'm getting rid of my old 2004 FZ6 engine with about 45k miles on it. Will pull small pieces off and ship if anyone wants them.
Just make me a reasonable offer to cover shipping and my time.
This is what happens when you use a cheap torque wrench:
In case you can't tell, that is a valve cover bolt stripped off deep inside. My torque wrench didn't click, and I wasn't intelligent enough to stop tightening the bolt.
I don't know whether I should attempt to drill it out...
Hey all, been a while since i posted, still riding my 2nd Fazer but came badly unstuck and need advice please.
Chain came off at about 80km/h, took out the mount for the front sprocket cover, plus a 6cm hole on the side of the block. I tried using pratley steel to cover it up but the engine...
Looking for a cover that suite my needs and fits the bike quite well.
Needs to be quite resistant against rain and would be cool of it could take some heat so I could fit it just after I park the bike at home.
Does not have to be flashy as it is primarily for parking up next to the house...
New clutch - Not enough spring-action... SOLVED!
Installed a new clutch (a set with compression springs, friction plates and clutch plates).
The whole operation was quite easy except refitting the clutch cover onto the pull rod. I followed the steps of the "2004 Service Manual" (around page...
Alright I am new to this forum but I have a 2004 Yamaha FZ6 and the side cover is black with metallic specs but is cracked and for the 2004 they only sell a Silver side cover and a Deep purplish blue and I bought the deep purplish blue one thinking it would be a really dark color and look black...
I was going down the street not too fast but probably faster than I should have being that there was snow on both sides of the road. The road itself was clear and as it was two blocks from my house I had been down the same road multiple times today and all was ok those times so I guess I was...
Hi All,
As the title says, I'm looking to buy an oil pan cover for a 2009 FZ6. I've looked around on ebay, but I haven't had much luck finding anything.
Thanks
WTB a good condition OEM Stator. Possibly interested in R/R as well and will consider buying stator cover if you've got one, but it would need to be silver (for a 2004).
I'm going to be replacing the crankcase cover on my 2009 FZ6, but was unsure about whether or not I need to use any sort of gasket sealant when I put the new one on.
I got a new gasket along with the new cover, but I couldn't find any information on if it's a rubber gasket, silicone, etc...
.... so in the off-season, I undertook a needed valve adjustment. It was detailed and slow going, but everything seemed to go as planned......until it came time to reinstall the valve cover. The new gasket was fighting me to stay flat against the valve cover, so I smeared a little RTV on the...
Help!
I've been trying to replace my stator and its cover and when I'm ready to install everything I can't get the rod from the gear to fit in side my new cover! Is there something I'm missing or anything I could do to make it fit, or did I just buy a **** cover?
Any help would be...
up for grabs here is an airbox cover with the mod done to it. Got from someone on this forum 5+ years ago. the cutout is so neat it hardly looks like a modification at all
Then I gave it to my good buddy S.D Willie who mounted a stebel air compressor inside the airbox (haha... yeah he did...
Will probably be ordering these from Ayers in a week or two, but wanted to see if I could find some used ones here first. (Ebay is useless as always and just returns oodles of FZ6R garbage.)
Cowling
Visors (side 1 and 2, silver. Blue experiment looked bad. Probably have a right visor to sell...
hey guys Happy Thanksgiving.
Went out for a ride today and notice a drip one of the radiator hoses here are some pics. And no I was not the one that dropped the bike the guy I got it from has it sprocketed down to use as a wheelie bike and laid it down a few times. But anyways there is a small...
2004 Yamaha FZ6 with just under 19,000 miles. It has grip heaters, belly pan, clutch slave and frame sliders. The bike is in top condition and has never been dropped.
The bike will also come with all the following accessories.... tank bag, two seat bags, two side bags, full cover, bra cover...