- Joined
- Jul 14, 2007
- Messages
- 1,825
- Reaction score
- 53
- Points
- 48
- Location
- adelaide australia
Mikey try total motor for your sprokets.
New Stuff on it's way - Part 3!!!
- Thread starter Wolfman
- Start date
Dont worry Jules, Mikey has already given up on Vortex, has now got a GYTR 520 rear sprocket, waiting to go on his beast!
:rockon:
Ok, after 7 months...yes, that is a WORLD RECORD! i finally got my Axle & Fork Sliders...and they FIT!
Pardon my sarcasm, but you wouldnt think a couple of sets of sliders could prove such a drama....
Well anyway, 1 accident where i would of real benefitted from having these little suckers later....i present my "Axle Armour"
View attachment 16769
View attachment 16770
View attachment 16771
View attachment 16772
View attachment 16773
View attachment 16774
They are made by the same people who make Oggy Knobs, and are very good quality....took about 2 minutes to fit!
I think they also look cool, clean up the base of the forks, and cover the very average looking axle nuts on the 06 swingarm nicely!
:rockon:
Pardon my sarcasm, but you wouldnt think a couple of sets of sliders could prove such a drama....
Well anyway, 1 accident where i would of real benefitted from having these little suckers later....i present my "Axle Armour"
View attachment 16769
View attachment 16770
View attachment 16771
View attachment 16772
View attachment 16773
View attachment 16774
They are made by the same people who make Oggy Knobs, and are very good quality....took about 2 minutes to fit!
I think they also look cool, clean up the base of the forks, and cover the very average looking axle nuts on the 06 swingarm nicely!
:rockon:
Last edited:
necrotimus
Stop looking at my title!
I have average looking nuts too... I may have to look into some of these. I agree cleans it up nicely!
Not before time. Looks nice mate.
Ok, as far as this thread goes, it's well old now, but i was always going on about getting a TCP seat cowl! Well i have one now...it's the wrong colour, but that's cool, cause i am going to paint the rest of the bike anyway now...
No photo's yet, but i have the seat cowl...last piece of "bling" in the puzzle!
:thumbup:
No photo's yet, but i have the seat cowl...last piece of "bling" in the puzzle!
:thumbup:
Cough, Coughcarbonrimsahem....sorry....lol...something got caught in my throat
.Cheers
Mike
Cough, Coughcarbonrimsahem....sorry....lol...something got caught in my throat
Cheers
Mike
Yeah...i been looking at those suckers again too...The BST carbon wheels are just pure "bike porn" at it's finest!
Pity they cost so freakin much!
Yeah...i been looking at those suckers again too...The BST carbon wheels are just pure "bike porn" at it's finest!
Pity they cost so freakin much!
I'm sure you'll find something else to blingify...lol.
I'm sure you'll find something else to blingify...lol.
Dunno have been thinking..the FZ6 has the nice light R6 wheels anyway...Cast Magnesium, or the likes, as it is anyway, so i may just be throwing good money at something i really dont need to do..
Dunno have been thinking..the FZ6 has the nice light R6 wheels anyway...Cast Magnesium, or the likes, as it is anyway, so i may just be throwing good money at something i really dont need to do..
Titanium exhaust?......lol....
Just throwing them out there:thumbup:
Titanium exhaust?......lol....
Was only speaking to someone yesterday about the possibility of getting titanium headers made up....i wonder how much it would cost??
There is someone in Adelaide that could do it too!
:rockon:
afpreppie04
The Thread Killer
- Joined
- Dec 30, 2007
- Messages
- 747
- Reaction score
- 6
- Points
- 0
- Location
- Rio Rancho, New Mexico
M4 makes a full titanium system for the 03-05 R6. Seeing as their headers can swap in place of ours you should be able to make it work from the headers up to the midpipe part, then put your exhaust on from that point back I would think. You can get the titanium system with a polished muffler for $913 directly from M4. I wonder if they would sell just the front half of the system separately?
Hmmmm... i never knew this...can you post a link to where i can get in contact with the guys from M4...will give them a call!
:thumbup::thumbup::thumbup:
afpreppie04
The Thread Killer
- Joined
- Dec 30, 2007
- Messages
- 747
- Reaction score
- 6
- Points
- 0
- Location
- Rio Rancho, New Mexico
Unfortunately their site is all flash so there isn't an R6 specific page. But the site is M4 Performance Exhaust Systems I can't seem to find an e-mail address, but they are located in Dallas and the phone number is (972)481-9300. I know its (super) long distance for you...maybe one of our Texan members can get ahold of them?
No stress, i will just work nout the time difference between here and Texas, and give them acall direct...someone ringing all the way from Australia should get their atention!!!
:thumbup:
