wire

So I recently had the edge to ride my bike and it was almost 0° out of course with my bad luck I put the bike down. So now I'm in the middle of doing a streetfighter rebuild on the bike I recently purchased a 7 inch round LED to mount on the front The original bike obviously had to had lights...

Hoping someone can help. I'm having a problem with the naked conversion wiring. The issue is that the hazard lights (synchronised strobing turn signals) don't work on the front when the hazard warning button is pressed. They do, however, come on when either turn signal is used. Neither of the...

Hi all, I've bought a power Commander for my FZ6, fitted and it all works fine. However I'd like to set up the coolant temperature with the PCV, so I've connected a wire to the 'analogue' port on the PCV and connected it to the green/white wire as per the instructions and it sort of works. I...

Any recommendations on where to connect positive wire for heated grips on a 05 FZ6. I am using these grips if it helps: https://www.amazon.com/gp/product/B009Z1KQ2M/ref=oh_aui_search_detailpage?ie=UTF8&psc=1

Hello, I want to change my 2006 fz6 Speedometer out for a 2007 fz6 speedometer . I have a 07 front conversion already so I can put the 07 speedometer , but the confusing part for me is the wiring and what to do. How do I wire it properly, is there a schematic or blueprint I can look at...

Short story is I bought a ratty 2005 FZ6 from a guy that laid it down to the point that the speedo is gone and the ignition has been relocated. I'm close to putting an aftermarket speedo and tach on the bike but am wondering about the neutral signal. I have found the below hack that the PO did...

I have purchase a cheap knock off digital tach/speedo gauge. Halfway to completing the install. I'm not going to bother with the Gear indicator but I have successfully powered it, hooked up the high beam indicator, turn signals, and speed sensor. RPM works off of the signal from the CPS or right...

I have to safety wire my my oil sump bolt, oil filer cap, oil filter, and possibly dip stick. Any ideas what the best anchor points would be? I've never done this before.

I really don't know what to say. It is a plug and play deal. Really good initial quality. Only "problem" I had is that you have to damn near disassemble the whole tail of the bike to install it. Zip ties are your friend due to the extra length of wire in the harness on the new light, which by...

Hi all, I’m a noob to working on motorcycles and the electrical system. I purchased this bike with the 7” round single headlamp conversion already done. The headlights low beam was intermittently flickering and eventually died. I changed the bulb and checked the fuse. The wiring harness looks...

Hi all I had the tank off my 2008 fz6s today and saw something I'm curious about. There is a red wire going from the positive battery terminal straight to the regulator rectifier, the bike runs fine I was just wondering since it doesn't look factory, is this normal or a by-pass or something?

Sold! Literal plug & play keyless ignition system by Digital Guard Dawg. I had this installed on my 2007 model using all stock connectors. The kit comes as a universal installation in stock form; I added stock ignition wire connectors and purchased a second stop switch assembly in order to make...

Lets just say this is a repeating event as the #2 wire has failed for the 4th time! The tell tale sign is vibes to the @ss through the seat! They start at 3800 RPM and are VERY noticeable through the whole 4K range. The brass screw pushes the copper wire strands off center! --> Click image to...

Hey guys! I need a little help. Last year, I completely disassembled the front of my 2008 Yamaha FZ6 Fazer because it was wrecked and I was thinking about a Naked conversion. Well, I decided against the Naked conversion and repaired the fairing instead. But there is this one wire...

So last week I dropped my tank and it pulled the wire out of the terminals and broke both connector plugs. Not a big deal I figured but I am having a difficult time finding the proper replacements that fit correctly. Does anyone know an aftermarket or OEM part# that I can purchase that will...

Okay, so I'm well acquainted with the need for a flasher relay rated for LED's due to their lower power consumption etc. What I've been working on is my custom wiring harness for my project bike, a 1979 Honda CM185, its a 6 volt bike and I wanted to run LED turn signals and brake light, so...

I said I wasn't going to splice any wires to get light but yeah...I am. I have 2 strips of led 12" long. I would like them to go towards the back to have more light in the rear. I haven't had a bike before with undertail exhaust. How hot does that get under there? Can I put the wire thru that...

Sold! (04-17-2013) Perfect condition headlight wiring harness removed from a 2007 Model. Great to have on hand for "naked" headlight conversions or speedometer conversions on 06' and earlier model years. Cord, Headlight Part Number: 4S8-84359-20-00 Factory MSRP: $110.95 Asking $50.00 o.b.o...