Finally installed the LED light

[Sycotic]

I like it!

 

[Billhockey1993]

Looks good I'm thinking of doing this at some point soon. Is it just plug and play?

 

[Sycotic]

It says its plug and play, but it wasn't that easy. Had to take the back plastic off to pop out the stock light, had to trial and error with the wires to make sure it would sync with the stock signals, blew one fuse. But overall it wasn't terrible, but entails more work than what it advertises. It's worth it though!

 

[H8 PVMT]

I bought this one,

2003 2004 2005 2006 2007 2008 2009 Yamaha FZ6 Sequential LED Tail Light

it's plug and play, easy to do and looks fantastic. My favorite part is that when you apply the brake the brake light flashes three times before staying on to help bring attention to the fact that you are slowing or stopping.

 

[Karate.Snoopy]

I bought this one,

2003 2004 2005 2006 2007 2008 2009 Yamaha FZ6 Sequential LED Tail Light

.

:thumbup: I have the same installed on mine, happy with the results

 

[shamrocker]

I bought this one,

2003 2004 2005 2006 2007 2008 2009 Yamaha FZ6 Sequential LED Tail Light

it's plug and play, easy to do and looks fantastic. My favorite part is that when you apply the brake the brake light flashes three times before staying on to help bring attention to the fact that you are slowing or stopping.

That is freakin' sweet! :rockon: Do you have the pod flashers down below, as well?

 

[dolau]

I have done it on mine but didnt connect the LED flashers- must get round to that somethime

 

[Sycotic]

I have the same one that you guys posted. I had to cut a few wires on mine.

 

[Wh0M3]

I got a similar looking LED tail light and had to search around to figure out how to install it. There are some great instructions on this forum for the install but it seemed to miss out on what to do with the wires. I found this video that was very helpful for the wiring. I know it's on a Ninja 250 but the wires are the same.

[ame=http://www.youtube.com/watch?v=TZb97LgSXKU]Bikelitez Integrated Tail light install. Ninja 250 - YouTube[/ame]

 

[Wh0M3]

also there is another thread with great info too.

http://www.600riders.com/forum/fz6-...led-tail-light-install-w-oem-turn-signal.html

 

[H8 PVMT]

That is freakin' sweet! :rockon: Do you have the pod flashers down below, as well?

No, everything under the tail with exception to the LeoVince is gone. The license plate is on the swingarm. In my opinion, it's a nice clean look.

 

[H8 PVMT]

Here is the look of my bike.

 

[joshiepoogoose]

Here is the look of my bike.

do you have pics of you swing arm mounted plate? im looking for ideas

 

[H8 PVMT]

do you have pics of you swing arm mounted plate? im looking for ideas

I bought this one off eBay.

Yamaha FZ1 FZ6 License Plate Relocator Bracket Mount | eBay

I had to trim it about an inch to make it look better because the holder was a little larger than the license plate and I'm a little picky about details. :BLAA:

Here is another pic, I trimmed the plastic bit between the pipes.

 

[Wh0M3]

just an FYI

I know some states do not allow for vertical license plate mounting. So you may want to check out your state laws to see if they have an issue with it. I didn't see anything about the curve but some may view it as trying to obscure it and try to pull you over for that.