Search results

Well not any before mod data for you, but exhaust and PCV, 38 to 42 on 09 S2 ridden moderately. Probably a bit less than before the mods, but not much. And the throttle response is much better.

It has been two years since I got my PCV working correctly and other than some map changes, nothing has been updated, Firmware is /was still 1.2. After checking around, I updated the firmware to the now current 1.8.13 level, and yes, no problems. With the early issues with the FZ6 , batch...

Please review my post's on this subject / and identical problem in this thread. The FZ6 requires special firmware due to the use of batch injection. Test with a zero map autotune disconnected and document the problem, then contact PC and get an exchange for correctly programed unit. (The FZ6...

Oh yes, the baffles. I had to play a bit to get mine out. Here is the way I did it. Rivets are removed and the baffle can be moved about 1/4 inch (5 -6 mm). Now get a pair of vise grips and clamp them tight to the top edge of the baffle. Take a adjustable crescent wrench and...

I think a Ducati trellis type frame from 4130 tubing would be incredible. 4130 is less expensive than SS, easier to work/weld and has excellent mechanical properties. Ti is actually probably too expensive and welding is tricky, and in bicycle frames is known as very flexible, at least mine is...

Try these people. I have had very good service from them and prices are good. Motorcycle Parts|ATV Parts|Honda|Kawasaki|Suzuki|Yamaha|Dealer|Wholesale Discount Prices Motorcycle Parts|ATV Parts|Honda|Kawasaki|Suzuki|Yamaha|Dealer|Wholesale Discount Prices Good luck.

+1 on PJ's Parts and Rizoma. I've looked at the Oil filler cap, and would like to see how it fits, so please post the Pic. Andy

Looking to upgrade the stock suspension and the units I have narrowed the rear to are the Penske 8900E, and the Hyperpro. Has anyone had any experience with either of these shocks, comments on quality, installation issues, adjust ability, etc. These seems to fit my intended use, street...

Yes, the throttle position is needed to allow the selection of the cell in the two dimensional matrix to be selected correctly. Otherwise you would have only a single column of values corresponding to RPM only, regardless of the throttle opening. It's simple to do, and then with a good map...

Your right, the weld are good, not bad, but not great by any means. Strange that the weld quality isn't the same as the attention to polishing the pipes, etc.

I'm not sure if it's the firmware or not, since they stated: "UNIT EXCHANGED UNDER WARRANTY" but they loaded a map and didn't up date the firmware so I think that it may be an issue or at least is something they are not sure of. Your analysis of software is probably correct. In fact...

Dynojet's package arrived yesterday, and they replaced the PCV unit, under warranty. I haven't installed the new box yet, and it will be this weekend at best, before I can get to it. But, they replaced the unit, so is it safe to assume that they found a problem with the prior unit, or is it...

Thanks for the heads up,. I found the bits you mentioned taped to some packing material,. Didn't even notice them before. A few minutes with a drill, and they now are screw attached. Thanks for the help on reducing things I send to the land fills by mistake. :D

The reasons that I found you could not install the Leo's without the included Cat eliminator on an 09 were three fold. 1) The inside diameter of the Y pipe would need to be a match to the outside diameter of the Yamaha Cat pipe. It is not even close, being 4 to 5 mm larger ID than the Yamaha...

I didn't include any sound comparison since sound is so subjective and I used the factory cat pipe with the Remus, an a cat elimination with the Leo Vince. But since you asked, here goes nothing: Remus With DB Killers and cat is not loud at all, but a very nice sound. A deep resonate...

Well, the Pipe City people had the Remus system delivered on Tuesday evening. I had already removed the Leo Vince system as a forum member wanted them, so the installation was a nothing task. So, why the post? Most people don't purchase and have two systems available for...

Don't know about legal (and if I did, it would be a Texas only answer), but it sure looks sweet. And ditto on the mirrors; what and where did you get them?

Good work, looks very good.:thumbup:

I checked all the options for any fuel inputs, but every was zero. Nice it would be to get a 2 ch scope on this. It would be a "Eureka, that's the problem" type moment. I'll post anything I hear. Andy

Actually I did additional "testing" to try and isolate what is going on prior to returning the unit to Dynojet. 4 difference setups, all with the zero map in the PC-V, engine warm with 180 water temp, where I would slowly raise the rpm to 3000, hold 3K for a few seconds and then release the...