FS: 15T Vortex Sprocket

[maverick1970]

SOLD

I'm selling a 15T Vortex sprocket for $12 + shipping. It has 3,000 miles on it.

 

[tasop7]

I have to do a little research on what tooth combination of front and rear sprockets will give me more torque, and I'll pm you shortly. Dibs for now... I'll post very soon if I'm going to pass.

But I'm guessing you'll know. I'm not 100% sure what the stock sprockets are, but how do the 15T front and 48T rear you're selling compare to stock? Again, I'm looking for more torque, not more top speed / better gas mileage.

Thanks! :thumbup:

 

[maverick1970]

Doing the -1/+2 conversion would definitely give you more torque. It does hinder you gas mileage but with power goes gas mileage

 

[ecudoc]

Just incase, I really wanna cover my tail here " 2nd dibs on all three (front, rear and chain)"

 

[fureinku]

money talks where im from, ready to buy now, let me know... paypal verified

 

[maverick1970]

Fureinku I understand where you are coming from but we are a community here. I notified tasop7 that others are interested and have given him a 48 hours. After that time, I'll contact ecudoc. If he isn't ready to purchase, I'll notify you. Thank you for you interest but I must be fair.

Best regards,
Jeremy

 

[stryken]

I did it... I loved it and it didn't impact my gas mileage much at all. You will notice more of a torque feeling with it. As said before its the way it should have been from the factory.

 

[motopete]

If the other guys fall through send all three my way

 

[tasop7]

Question... according to this post, http://www.600riders.com/forum/fz6-mods/15579-520-chain-conversion-1-front-2-rear-vortex-setup-2.html#post196838, jazzpaintball says these sprockets last between 4,500-6,000 miles before needing to be replaced. Can you comment on that? The ones you're selling are aluminum right? Steel does last longer, but is there any disadvantage to it?

Thanks Jeremy for honoring my first post, really appreciate that. I've been looking into this mod for a while, and I'm just trying to find the right combination for me. I'm also just trying to find out how much life is left in the sprockets and chain you're selling... I don't want to worry about replacing again very soon.

 

[stryken]

Question... according to this post, http://www.600riders.com/forum/fz6-mods/15579-520-chain-conversion-1-front-2-rear-vortex-setup-2.html#post196838, jazzpaintball says these sprockets last between 4,500-6,000 miles before needing to be replaced. Can you comment on that? The ones you're selling are aluminum right? Steel does last longer, but is there any disadvantage to it?

Thanks Jeremy for honoring my first post, really appreciate that. I've been looking into this mod for a while, and I'm just trying to find the right combination for me. I'm also just trying to find out how much life is left in the sprockets and chain you're selling... I don't want to worry about replacing again very soon.

I think that the aluminium rear sprocket might wear this quickly not the front one its steel.

 

[maverick1970]

I'm sorry tasop7, but I'm not qualified to answer the questions you are asking.

 

[tasop7]

After lots of reading about this mod, I'm going to start of by trying just the 15T front sprocket and keep my stock chain and rear sprocket. Since you have all 3 pieces for a perfect -1/+2 conversion, I'll let it all go to ecudoc.

Thanks again Jeremy! :thumbup:

 

[maverick1970]

Everyone has backed out. Item is wide open.

 

[maverick1970]

Front sprocket has been sold. Thank you Gary!