Recent content by GravisMaximus

Got them today, wow only 3 days.... super fast handling and shipping. Any way the dot dates are 4513 and 3813 so they we only on the shelf four months. Now I just have to wait till spring to test them :Flash:

if you do engine mods or install a power commander etc.. do you have to make a eliminator (resistor) to that set-up? i ask because of what i have found with mine, i measured the o2 signal with the bike running and found that my o2 millivolt reading had a average .725v 1-5k rpm and 7-10k rpm...

I know there apples to oranges.... was looking to know what the mileage is approximately on them. So thanks everyone for the response. After having the corsa 3 and getting 3k on them 6k is double and I get to keep the grip? Sold!!!:rockon: just bought the power 3s, hope I get that double...

That always seems to happen, lol :spank: but I tried to get the focus on just the two tires. I run crosa 3's now and loved them, but only get 3k from them. Want a tire I can get 6k from. Do you think the power 3s can do it? I like the tread design more and not having sipes going to the egde has...

Time for a new set of tires. These are my two choices. Note its not the ,road 3. Would like your input on mileages and dry grip. I found the michelins for 30 less. What one would you go with and why.

i have a question for 07+ owners, if you unplug the o2 sensor will it set a code? being a auto tech myself id say yes, but ive read on fourms where people say it dont. so if you have unplugged it and it dont set the light please let me know. i was looking at getting a 02 sensor eliminator...

I was thinking almost the same thing on the way home tonight. In regards to the no load reading. I also thought its probably not a rpm its doing it but rather a certain position on the tps. I'm just seeing it at 5-7k because there's no load. With that said what's the ecm doing at say 5-10%...

OK so its been a couple weeks since I did the decat and muffler debaffle, my first o2 readings looked just fine. But I decided to recheck this weekend seeing how I was doing a throttle bodysync, and I've noticed the tone of the exhaust changes in different rpms (not the way it should). The...

On my way out the door to pull the ais off when I got thinking, why? If the ais only opens below 140° and at idle then going down the road it should be off. When I took those o2 sensor readings the bike was at operating temp 180° and tested both at idle and 7-8k rpm. So if I'm running rich now...

I have driven it back and forth to work the last two days, no codes and don't expect any. As for performance I want to say its lost very little low end torque under 6k but it has. It is a bit sluggish until 6k but after that whohoo.:rockon: The free flow exhaust does seem to get me into the...

as you can see i also put in a deflector (used inner muffler parts) same design flowmaster does. I cut the outlets with a bi metallic keyhole saw after I removed the baffles. and used part of the muffler chamber tubes for bridging the gap between the can and the exhaust tip. over all...

Finished the exhaust mod, heres what I did i removed the header pipe cut the outlet off and removed the precats welded it back together. Removed the mid cat and reinstalled. Removed the muffler, debaffled it increased the outlets to 1 3/8 welded the muffler and reinstalled. The sound is a much...

i was able to talk to the company that is selling this eliminator, to sum it up there is indeed a jumper connecting the pins. the jumper is a resistor!! so anyone who has one of these could you please take the boot off from the back of it and tell me what the colors are on the resistor and...

well i went ahead and ordered the scan tool, it is on a slow boat from china. it says it has lots of pics to show where to hook them up. will let you know if it works when it gets here.

Looking at my wiring diagram I went looking to find out what the 4 pin connector was i found mentioned in my other post. I can not find it in the diagram!! I also hve other wires that i suspect to be for additional lights that are not on the diagram,. There not telling us everthing...