rear

Hello everyone, my name is Nicolae and I am from Romania. Here is my bike from 2004 with two recently mods that I made. In the front new tube with new caliper and on rear side I changed the subframe and swingarm. All the parts are from S2 and are plugged/play. Enjoy:)

Hello! Complete newbie on this forum, fz6's and customising in general I'm completely baffled by the following problem I own a 05 fz6 s2 I have just installed a Dominator exhaust, LED rear tail/brake light, tail tidy with single LED no. Plate light with to Arrow carbon look rear...

My bike came with a fender eliminator, so the signals are mounted on the license plate bracket. (if this is important?) I went for a ride Friday, and when i got off the bike i noticed one of them was hanging by the wires. The rubber that is suppose to be supporting it had broken off. I...

Preface: I made a custom exhaust and wound up melting my rear turn signals, the wiring and stalks. Luckily I had an integrated taillight, so that worked, but I didn't feel that comfortable with it. So I decided to make new turn signals. In making the new exhaust, I'd slimmed down the tail end...

No Longer for Sale Swingarm is in good condition with a few cosmetic blemishes from use over the years; Photos should tell the complete story. Perfect working condition. Comes with everything needed to install on a 04-06 model. These do not come around often so scoop it up while you can...

Prefer color Yamaha blue. But if I get some tips on how to paint it correctly I can do that work myself. I've been searching the salvage parts sites and the like but no luck. If you know where I could find one cheaper than Yamaha dealer the information would be great!

I am having a few problems installing my new Tail Tidy kit from Evo tech. Firstly there are 3 wires leading from the standard Tail ( 2x indicators and No.plate light ) and the indicator leads disconnect but the No.plate light divides into 2 wires, both cant be disconnected..Im just wondering...

SOLD!! (08-23-2011) This sub-frame was removed from a 2007 model but will fit all years. The later model sub-frame gives the added advantage of having removable passenger pegs (not included) which was not available on the 2004-2006 model. The part shows only normal signs of wear (some paint...

SOLD!! (07-29-2011) Grab rails were removed from a Blue 2007 Model but will fit all 2007-2009 models (I believe it will fit 04'-06' models as well. Can anyone confirm?). Functionally, the part is in excellent condition with no broken mounting tabs or evidence of a crash. Cosmetically, it could...

SOLD!! 06-30-2011 A much coveted, Gen II Swing-arm with rear axle, adjuster blocks, seals, bearings, and chain guard: Ready to bolt on to an 04' - 06' Model! The part is in good condition with only normal wear from road debris. The areas which show wear (Mainly the top section and area to the...

Sold! Another left-over from the ZX6 Conversion. Will include the axle, nut, washer, and chain adjustment blocks. Will fit 2007-2009 model years. Axle Part #: 5SL-25381-10-00 Axle MSRP: $58.72 Left-Chain Block Part #: 5SL-25389-00-00 Left Block MSRP: $32.57 Right-Chain Block Part #...

So after checking out my rear tire the other day, I noticed that the carbon fiber (more than likely imitation) rear hugger the previous owner installed is completely crooked. I took out all 4 bolts + the center plastic pin. I managed to wiggle/work the hugger out without having to remove the...

I decided to get a 530 48T rear sprocket to give a little umph. My only question I haven't found specifically answered is, Do I need a longer or shorter chain If I just go up 2 teeth in the rear only? I am buying a sprocket for a 530 chain, I think like stock, with 2 more teeth than stock. I...

Love this, base model Ohlins, basic threaded preload adjustment, and rebound damping...but very nice.