Search results

  1. B

    Monolock Givi Topcase on Yamaha Rack

    Do you still have this item for sale???
  2. B

    How to Change my Throttle Position Sensor (TPS)

    Nice recap really nice :thumbup:
  3. B

    How to Change my Throttle Position Sensor (TPS)

    lol Blah Thanks once again :D
  4. B

    How to Change my Throttle Position Sensor (TPS)

    Ok!! The plugs finally arrived and have been changed. That's what we have to go through here in Nigeria, you have to "wait" after you make your order After the change bike was still acting up. Good enough I changed the plugs at the mechanic shop so he suggested we check the pump. Apparently...
  5. B

    How to Change my Throttle Position Sensor (TPS)

    Thanks I haven't noticed any Black Smoke. And yes the 1st video was a cold start. I also cleaned the Air Filter when I changed the TPS Yet to get the plugs. Hopping it arrives this weekend. I'll search the forum on how to change plugs Thanks Thanks I'll keep you posted :Flash:
  6. B

    How to Change my Throttle Position Sensor (TPS)

    Tried posting these videos but they were too large, so had to upload it to dropbox These are links to video clips showing how the bike sounds: https://www.dropbox.com/s/wq6bzrpvwo7w305/VID_20150127_214817.mp4?dl=0 https://www.dropbox.com/s/nc14i82he2utov5/VID_20150127_214108.mp4?dl=0...
  7. B

    How to Change my Throttle Position Sensor (TPS)

    Yes idle redlines to 14k I guess I'll have to take a video of how it responds. & yes it used to run properly at a point in time :D
  8. B

    How to Change my Throttle Position Sensor (TPS)

    I think it runs the same way it ran before the TPS was changed On idle the engine jumps from 900-1200 Yeah I pulled out the throttle bodies. Did it with a friend so we were careful to plug all plugs properly. Just attached a picture Thanks
  9. B

    How to Change my Throttle Position Sensor (TPS)

    Thanks Final Impact, The TPS swap went smoothly. Also calibrated it with the diagnostic on the dashboard It revs after 4500rpm I'm bout to order a set of Iradium plugs (NGK CR9EIX), hope that's ok. I'll check plug caps too Also I haven't checked the tank and injectors (which I was...
  10. B

    How to Change my Throttle Position Sensor (TPS)

    Hi, So I finally got the time to change the TPS :cheer: Thanks for all the help. I've attached two pictures of the diagnostic reading when the throttle is open and closed. Closed = 15 and Open =100. I hope this is acceptable The bike sounded better but I still have, the bike is still...
  11. B

    How to Change my Throttle Position Sensor (TPS)

    FinalImpact Thanks Thanks Thanks!!!!!!! Will be working on it this weekend. Will keep you posted
  12. B

    How to Change my Throttle Position Sensor (TPS)

    Hi All, I noticed uneven idle on my TPS & a reduced mpg. I also followed a thread on how to diagnose the TPS http://www.600riders.com/forum/fz6-technical/181-throttle-position-sensor-issues-you-experiencing-poor-idle-mileage-stalls-18.html?highlight=throttle+sensor+position I came to a...
  13. B

    '08 FZ-6: ER_1 Code...help please

    Explanation from top left: 1) Headlights down & back of the dashboard removed 2)Broken pin in the harness connector 3)Trying to bypass the pin by using an external wire to connect the wires originally connected to the broken pin 4)Dashboard back on holster 5)Bypass completed on both wires...
  14. B

    '08 FZ-6: ER_1 Code...help please

    Thanks Cloggy :thumbup:
  15. B

    '08 FZ-6: ER_1 Code...help please

    I'm having issues with uploading pictures from my computer. When I can figure it out I'll post the pictures Would appreciate any directions on how to go about it
  16. B

    '08 FZ-6: ER_1 Code...help please

    I dread electrical problems :(
  17. B

    '08 FZ-6: ER_1 Code...help please

    :don'tknow: Had same issue just less than 2 months ago. Took my bike to an electrician to sort because the HID lights wouldn't come on. Shortly after he sorted the lights out I saw the Er_1 code on my dash. I almost got hypertensive. :(:o :eek::eek: Took it back to the guy but he couldn't...
  18. B

    My Engine Stalls for the first 5min

    When it started I installed the K&N Air Filter. Thinking it will help
  19. B

    My Engine Stalls for the first 5min

    Brov you know exactly how my bike feels @"Engine never died on me, just feels reluctant to rev" :thumbup: Please when you put the oil on your K&N Air Filter did it help:confused:
  20. B

    My Engine Stalls for the first 5min

    Thanks for the pictures I'll check on the vacuum port link once I get home
Top