Hello & Welcome to our community. Is this your first visit? Register

Thanks Thanks:  11
Likes Likes:  21
Dislikes Dislikes:  0
Page 1 of 4 123 ... LastLast
Results 1 to 10 of 36
  1. #1
    Fz6 2007 (OP)
    Junior Member Fz6 2007's Avatar
    Join Date
    Nov 2018
    Location
    Pittsburg,KS
    Posts
    28
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Blog Entries
    2

    Cut Harness 2007 fz6 code 19

    Code 19 after attempted theft, rewired the harness and bypassed side stand switch . I have cleared at diagnosis 62 after , but still coming back...cranks but no fire .. anybody got a wiring diagram for this ? thanks ... any ideas...
    Attached Thumbnails Attached Thumbnails Cut Harness 2007 fz6 code 19-img_20181030_114048-jpg  

  2. #2
    Fz6 2007 (OP)
    Junior Member Fz6 2007's Avatar
    Join Date
    Nov 2018
    Location
    Pittsburg,KS
    Posts
    28
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Blog Entries
    2

    Re: Cut Harness 2007 fz6 code 19

    I have another question, at 62 in Yamaha diagnostic ...60 says 0 and 61 used to say 19, but not now... still won't start but turns over good, nur
    tral light comes on while in neutral... still no start... when I get to 62 I have been able to clear by cycling kill switch
    ... But not now... any ideas to solve this... please help if you can... it's a daily driver before it was stolen and hacked up

  3. #3
    Fz6 2007 (OP)
    Junior Member Fz6 2007's Avatar
    Join Date
    Nov 2018
    Location
    Pittsburg,KS
    Posts
    28
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Blog Entries
    2

    Re: Cut Harness 2007 fz6 code 19

    Also just in case there's a connection with this problem, my brake light doesn't work with either the hand or foot brake applied ... just trying to provide all things that could be related ... Any Thoughts?

  4. #4
    Fz6 2007 (OP)
    Junior Member Fz6 2007's Avatar
    Join Date
    Nov 2018
    Location
    Pittsburg,KS
    Posts
    28
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Blog Entries
    2

    Re: Cut Harness 2007 fz6 code 19

    So I press both select and reset ,then turn key on ... Wait 8 seconds or so: then do it again for like 4seconds . The screen goes to Yamaha SELF DIAGNOSIS...d1 is throttle...etc
    At d62 I should be able to reset/clear a code...by cycling kill switch?... This is where I get lost , how to clear in d62... currently d62 reads 1& d61 used to read 19 and d60 used to read 1... Disconnected battery
    ...now d60 is 0, d61 is 0 but d62 is 1....
    Help... Thanks !!

  5. #5
    Fz6 2007 (OP)
    Junior Member Fz6 2007's Avatar
    Join Date
    Nov 2018
    Location
    Pittsburg,KS
    Posts
    28
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Blog Entries
    2

    Re: Cut Harness 2007 fz6 code 19

    h electronic fuel injection.
    ******************************** 01 : Throttle position - must be from 15-17 (closed) to 97-100 (opened) 02 : Atmospheric pressure given in mmHg (normal is 760 - average weather) 03 : Differential pressure between air and intake pipe 05 : Air intake temperature (in Celcius) 06 : Cooling liquid temperature (in Celcius) 07 : Absolute speed (must be 000 in garage). Check with rear weel. 08 : Lean angle safety switch control - must be from 0.4-1.4 (upright) to 3.8-4.2 (horizontal). DISMOUT THE SWITCH FOR CHECKING !!! 09 : Battery voltage - must be above 12.0 20 : Side stand switch - displays ON or OFF 21 : Neutral gear switch - displays ON or OFF Part II : ECU memory check. 60 : EEPROM error code presence - 00 means no default, 01 or 02 means default on corresponding cylinder (blinks if both cylinders). 61 : Error Code memory log - Displays 00 if no error code in memory, displays the Error Code if any (11 to 50). Display changes every two seconds if more than one Error Code in memory, then start again from first. 62 : Displays the number of Error Code in memory. To clear the memory, switch the Engine Run Switch to ON position (no backup). 70 : Check Code number, display from 0 to 255 Part III : Activators - To activate, turn Engine Run switch from OFF to ON - Engine check light is activated too. 30 : Coil 1 is activated 5 times per second. 31 : Coil 2 is activated 5 times per second. 36 : Injector 1 solenoid is activated 5 times per second. 37 : Injector 2 solenoid is activated 5 times per second. 48 : Air duct solenoid is activated 5 times per second. 49 : Air intake solenoid is activated 5 times per second. 50 : Fuel injection relay is activated 5 times per second. 51 : Cooler fan is activated every 5 seconds. 52 : Headlight relay is activated every 5 seconds (2 seconds ON, 3 seconds OFF) - 2003+ model only. Error Codes Error Number 11 : Cylinder identification sensor error - DIAG mode (none) Error Number 12 : Crankshaft posiiton sensor error - DIAG mode (none) Error Number 13 : Air intake pressure sensor error - DIAG mode 03 Error Number 14 : Air intake duct error - DIAG mode 03 Error Number 15 : Throttle position sensor error - DIAG mode 01 Error Number 19 : Sidestand sensor error - DIAG mode 20 Error Number 20 : Air pressure sensors error - DIAG mode (none) Error Number 21 : Coolant temperature sensor error - DIAG mode 06 Error Number 22 : Air intake temperature sensor error - DIAG mode 05 Error Number 23 : Ambient air pressure sensor error - DIAG mode 02 Error Number 24 : O2 (lambda) sensor error - DIAG mode (none) Error Number 30 : The bike went down - DIAG mode 08 Error Number 33 : Coil 1 open circuit - DIAG mode 30 Error Number 34 : Coil 2 open circuit - DIAG mode 31 Error Number 41 : Tilt sensor error - DIAG mode 08 Error Number 42 : Speed sensor error / Neutral sensor in short-circuit - DIAG mode 07-21 Error Number 43 : Battery voltage control error - DIAG mode (none) Error Number 44 : EEPROM read/write error - DIAG mode 60 Error Number 50 : ECU memory error - DIAG mode (none) Error Er-1 : ECU link error Error Er-2 : ECU link error Error Er-3 : ECU link error Error Er-4 : ECU link error Following ERROR codes DO NOT allow engine to run : 11-12-19-30-41-50 and Er-1 to Er-4 Error code 11 allow engine to continue running only if fault appears after engine start. Following ERROR codes DO allow engine to run but need immediate check because default values are taken by the ECU: 13-14-20-21-22-23-24-24-42-43-44 *....
    Is what I find so far... searching...

  6. #6
    Fz6 2007 (OP)
    Junior Member Fz6 2007's Avatar
    Join Date
    Nov 2018
    Location
    Pittsburg,KS
    Posts
    28
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Blog Entries
    2

    Re: Cut Harness 2007 fz6 code 19

    Ok , so I got tomorrow off so I can try and solve this ...please help ... and thanks

  7. #7
    Fz6 2007 (OP)
    Junior Member Fz6 2007's Avatar
    Join Date
    Nov 2018
    Location
    Pittsburg,KS
    Posts
    28
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Blog Entries
    2

    Re: Cut Harness 2007 fz6 code 19

    https://www.600riders.com/forum/fz6-...ce-manual.html
    This sticky says fault code 19 is not about side stand switch but about no4 ECU connection/circuit ...this sounds more like my problem- With cut harness... I've cleaned the contacts in the side stand switch... nothing... I've bypassed the side stand switch and even disconnected it ... Still nothing...
    What next... any body know where the no4 ECU wire goes so I can test it's continuity ???
    BTW it's an 07 (production date 12/06 ) FZ6 VIN:JYARJ13E47A002027
    Help
    Last edited by Fz6 2007; 11-21-2018 at 09:28 AM.

  8. #8
    Junior Member Gary in NJ's Avatar
    Join Date
    May 2014
    Location
    Amoungst the Twisty Roads
    Posts
    314
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Re: Cut Harness 2007 fz6 code 19

    I feel bad you, posting with no answers.

    From my understanding non-US spec FZ's have an immobilizer on the ignition circuit and the ignition switch itself that requires a key with a magnetic insert. Because of this I've heard that the inexpensive replacement switches on eBay don't work on non-US spec bikes. With that said, perhaps the immobilizer circuit is present in US spec bikes to keep someone from hacking into the harness with an external ignition switch. Once the circuit is opened the ECU may require a reset.

    If no one chimes in soon, perhaps a visit to a local Yamaha dealer would yield a result. I'd bring the title of the bike with you as without it questions about a hacked wire harness may seem suspect.
    Lifelong student of motorcycling. Current bikes: Custom Naked '05 FZ6, LS650 Café Racer, DRZ400 Street Tracker

  9. Likes Fz6 2007 liked this post
  10. #9
    Fz6 2007 (OP)
    Junior Member Fz6 2007's Avatar
    Join Date
    Nov 2018
    Location
    Pittsburg,KS
    Posts
    28
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Blog Entries
    2

    Re: Cut Harness 2007 fz6 code 19

    Thanks , no worries about feedback...I am patient...

  11. #10
    Vrrroooooom! Cut Harness 2007 fz6 code 19 Motogiro's Avatar
    Join Date
    May 2008
    Location
    San Diego, Ca.
    Posts
    13,516
    Mentioned
    89 Post(s)
    Tagged
    0 Thread(s)

    Re: Cut Harness 2007 fz6 code 19

    What color is the #4 wire to the ECU you reference? The documentation does not list a wire number in the schematic.

    Are you lacking spark, fuel delivery or both? When you turn the key to on do you get the fuel pump priming sound?

    When I hear the FZ6 starter spins but the engine won't fire I also think of the lean angle switch.
    Last edited by Motogiro; 11-21-2018 at 10:29 AM.
    If you can't fix it by hitting it with a hammer, it's electrical!

    Clif
    SoCal Hoon

  12. Thanks Fz6 2007 thanked for this post
    Likes Fz6 2007 liked this post
 

 
Page 1 of 4 123 ... LastLast

Similar Threads

  1. F/S Headlight Harness Wires Cord 2007+
    By fazil in forum Bikes/Parts For Sale
    Replies: 0
    Last Post: 05-14-2014, 01:20 AM
  2. Help!!!!!In need of 2007 FZ6 Wiring Harness and speedo
    By Bison in forum Bikes/Parts For Sale
    Replies: 0
    Last Post: 05-21-2012, 08:21 AM
  3. 2007+ gauges and front harness
    By the SS show in forum Bikes/Parts Wanted
    Replies: 5
    Last Post: 12-21-2011, 03:30 PM
  4. Replies: 11
    Last Post: 09-14-2010, 06:27 PM
  5. Replies: 12
    Last Post: 04-04-2010, 11:38 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
All times are GMT -7. The time now is 11:29 PM.
4.2.5
Image resizer by SevenSkins
Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Feedback Buttons provided by Advanced Post Thanks / Like v3.6.3 (Lite) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
User Alert System provided by Advanced User Tagging (Lite) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Copyright ©2007 , All content is property of 600Riders.Com All Rights Reserved. The opinions and posts on this site do not neccesarily reflect those of the site owners or operators.
Yamaha FZ6 and Yamaha rights are property of Yamaha Motor Company. 600Riders.com is not associated with Yamaha in any way. We are an enthusiast site dedicated to the Yamaha FZ6 motorcycles. Our goal is to offer a place for Yamaha FZ6 owners to discuss rides, events, mods, maintenance, purchasing, etc
vBulletin Skin By: PurevB.com